电工钢硅钢片绝缘涂层特性7.2.1 绝缘涂层状态产品通常以两面涂敷绝缘涂层状态交货，涂层种类见表 2。绝缘涂层应可耐受绝缘漆、河北保定当地变压器油、河北保定附近机械油等介质的侵蚀。本文件规定的绝缘涂层与国内外相关技术规范规定绝缘涂层的近似对照可参见附录 A(资料性附录)，无取向电工钢绝缘涂层的特性见附录 B(资料性附录)。绝缘涂层的厚度、河北保定附近自粘接涂层的剥离强度等技术要求如有特殊要求应在订货时协商，并在合同中注明。7.2.2 绝缘涂层附着性根据附录 C（无取向电工钢绝缘涂层附着性检测和评级方法），产品的绝缘涂层的附着性级别按照附着性由高至低分为 A、河北保定附近B、河北保定附近C、河北保定附近D 四个级别。供货时，产品涂层的附着性级别 应达到C 级。在剪切过程和供方规定的热处理条件下进行热处理时，涂层不得有大面积脱落，但是在剪切边缘位置，涂层的轻微碎裂则允许存在。7.2.3 涂层绝缘电阻涂层绝缘电阻分为表面绝缘电阻和层间电阻，表面绝缘电阻单位为Ω·cm2/面，层间电阻单位为Ω·cm2/片，理论上，层间电阻是表面绝缘电阻的 2 倍。根据需方要求，经供需双方协商，可进行涂层绝缘电阻的检测，并在合同中注明涂层表面绝缘电阻或层间电阻的小值

电工钢硅钢片Electrical steel, also known as silicon steel sheet, is an indispensable metal material in the power, electronics, and military industries, and is also the largest functional material in production. It is mainly used as the iron core for various motors, generators, and transformers. Since it is a functional material, its performance testing also revolves around "function". These indicators are often mentioned in trade and processing processes, and a brief understanding can help everyone better carry out their work. The performance testing of electrical steel mainly includes the following aspects: magnetic inspection, stacking coefficient inspection, coating adhesion inspection, repeated bending inspection, size and shape surface inspection, and conventional mechanical property inspection. In addition to the types of products listed above, there are also some special purpose electrical steel plates, such as 0.15 and 0.20mm thick 3％ Si cold-rolled non oriented silicon steel strips and 0.025, 0.05, and 0.1mm thick 3％ Si cold-rolled oriented silicon steel strips, which are used as intermediate and intermediate grade High frequency motors and transformers, as well as pulse transformers, etc； 0.7mm thick 3％ Si high-strength cold-rolled non oriented silicon steel plate for relays and power switches； High strength cold-rolled electrical steel plate for new high-speed motor rotors； Low carbon electrical steel hot-rolled thick and cold-rolled plates for magnetic shielding and high-energy accelerator electromagnets such as medical magnetic resonance tomography scanners； 4.5％ to 6.5％ Si high silicon steel plates for high-frequency motors, transformers, and magnetic shielding. Generally, motors, transformers, and other electrical components are required to have high efficiency, low power consumption, small size, and light weight. Electrical steel plates are usually guaranteed to have magnetic properties based on core loss and magnetic induction strength. Magnetic induction strength is the number of magnetic lines passing through a unit cross-sectional area of the iron core, also known as magnetic flux density. It represents the material‘s magnetization ability, measured in T. The magnetic induction strength of electrical steel plates is high, and the excitation current (also known as no-load current) of the iron core is reduced. Copper and iron losses are also reduced, which can save electrical energy. When the power of the motor and transformer remains constant, the magnetic induction intensity is high, and the design Bm can be increased. The cross-sectional area of the iron core can be reduced, which reduces the volume and weight of the iron core, and saves the amount of electrical steel plates, wires, insulation materials, and structural materials used. This can reduce the total loss and manufacturing cost of the motor and transformer, and is beneficial for the manufacturing, installation, and transportation of large transformers and motors. The main requirements for the performance of silicon steel are: 1. Low iron loss is the most important indicator of the quality of silicon steel sheets. Various countries classify grades based on iron loss values, with the lower the iron loss, the higher the grade. 2. Under strong magnetic fields, the magnetic induction intensity (magnetic induction) is high, which reduces the volume and weight of the iron core of the motor and transformer, saving silicon steel sheets, copper wires, and insulation materials. 3. The surface is smooth, flat, and the thickness is uniform, which can improve the filling coefficient of the iron core. 4. Good lamination performance is more important for manufacturing micro and small electric motors. 5. The adhesion and weldability of the surface insulation film are good, which can prevent corrosion and improve the punching performan